10 best jackhammers
A jackhammer is a narrowly targeted tool designed for preparatory work in construction or repair. A large assortment on the market allows you to choose a bump stop with optimal qualities corresponding to the nature and type of work. For chipping channels in the wall, when laying wiring or hidden placement of plumbing and heating systems, an average power bump stop is suitable. For dismantling tiles, plaster, etc. a small hammer with limited power will do. But for the destruction of asphalt and concrete pavements, demolition of old foundations, brick or other masonry, you will need a powerful professional tool.
You should also consider the type of bumper. When carrying out repair work, an electric tool is considered the best. It is convenient and quiet, of course, if there is a working electrical network, but when working in rooms with a high level of fire hazard or in a very dusty environment, it cannot be used. For construction sites, in view of the scale of the work performed, a pneumatically driven chipper will be more practical. It has high fire-fighting characteristics, is economical, and its power plant has a significant service life. There is also an instrument in which the impact force is generated by a gasoline two-stroke engine. Under certain conditions, this type of tool may be the only possible option, however, the increased noise level, toxicity of exhaust gases and high vibration does not leave such a unit in our rating.
When choosing a jackhammer for the job, you should consider the following characteristics:
- Maximum impact energy (J.);
- The frequency of beats per minute;
- Power, kWt.);
- Type of power consumption of the tool (pneumatic or electric);
- Brand (quality).
The force of the hammer blow is of fundamental importance, since it depends on what tasks the bump stop can handle. In electric tools, power is of equal importance - the higher the indicator, the wider and more complex the tasks can be set. Low power can only be compensated for by the frequency of beats per minute - the higher it is, the more destructive the force of the bump stop. Correctly calculated parameters of these values can be seen in the best models of jackhammers. With an average impact force and power, these tools have a high performance.
Bosch and Makita are considered the undisputed leaders in the professional tool market. The tools of these brands are of high quality workmanship, have a margin of safety and a long service life (much more analogues). The cornerstone when choosing a bumper for these brands is its cost - in the category of similar products, the price will be higher. The rating review below contains the best models, in our opinion.
Best Electric Jackhammers
The electric jackhammer operates on a standard 220 volt mains supply. Its main advantage is the absence of additional elements in the system. You just plug the tool in and you can use it. True, there are also disadvantages regarding power limitations. Pneumatic hammers are more powerful and more economical, but due to a certain complexity in their work, they are more often used in industries or large construction projects. In a domestic setting, an electric hammer is the best option.
5 UNION PES-2520RB
If you are not a professional builder, but there is a need for dismantling work, this model is of interest. For a very affordable price, you can buy a jackhammer with a good impact power of 49 J. An electric tool consumes 2 kW / h, is unpretentious and quite reliable.
Feedback from owners who have been using the bump stop for more than one year confirms its reliability and high performance. With its help, a wide variety of tasks are solved, such as: demolition of old buildings and foundations; preparation for excavation of rocky soil; removal of the frozen soil layer; crushing of rocks, sandstone and many others. For ease of use, an additional handle is provided. In the intervals between use, there is a special case for storing the tool.
4 CALIBER Master OM-1700M
It is believed that an electric hammer, even if it is Bosch or Makita, by definition cannot be more powerful than a pneumatic one, but this example completely refutes this statement. This is a really powerful instrument with an impact force of 65 joules. This is a lot, and even pneumatic jackhammers cannot always boast of such indicators. The power consumption is only 1.7 kilowatts, which is the norm.
True, it should be understood that such a force could not but affect the size and weight of the instrument. The hammer weighs more than 25 kilograms, and it will be very difficult to work with it, especially given the strong vibration of the electric motor. But he can easily demolish even the thickest concrete partition. There are also disadvantages regarding the noise level, which is also quite natural, given the design of the instrument. It works very loudly, as, indeed, any jackhammer, no matter electric or pneumatic.
3 Makita HM1203C
The design of the hammer and the presence of a side handle with a variable position makes the Makita chipper convenient for vertical work. A large power for this class - 25.5 J., allows not only making recesses and niches, but also easily punching openings in reinforced concrete walls, quickly dismantling brick and cinder block masonry. He is able to remove the floor screed.
The weight of the tool is 9.2 kg. The advantages include the ability to rotate the nozzle, adjust the speed and a comfortable handle with vibration damping function. Reviews of builders characterize the tool as reliable and durable, subject to timely service (change of brushes, lubrication, cleaning from contamination). Of the shortcomings, the only thing that is noted is the cost of the hammer. There is also an unreasonably biased attitude towards models made in China.
2 Bosch GSH 5 CE Professional
Despite being comparable in size to a conventional rock drill, a Bosch electric hammer can handle a wide range of jobs. With an impact energy of just 8.3 Joules, this demolition hammer easily crushes reinforced concrete castings. Its compactness makes it convenient to use for internal repair work. Low noise level (86 dB.), Vibration damping system with the help of a spring-loaded handle, adjustment of the number of blows, make the bump stop the best in its class.
Feedback from builders using the Bosch GSH 5 CE drummer in their work is generally positive. The convenience of chipping walls, removing plaster is noted - there is enough power for such work. Craftsmen talk about the successful use of a professional hammer to remove the old screed in the apartment. The ergonomic handle makes it easy to work - the weight of the tool is felt much lower than the nominal (6.2 kg.).
1 Makita HM1812
The best electric hammer capable of breaking strong concrete structures. Advanced AVT technology has significantly reduced tool vibration during operation, which increases the comfort of use. The Makita bump stop is able to work for hours without reducing its performance. The impact power is 72.8 J. - a value not yet available to other models of this class.
Reviews of builders who use a jackhammer in their work highly appreciate this model. The difference in performance is noticeable to the naked eye. At large volumes, this matters - when working with a Makita hammer, much less time is spent on dismantling.Of particular note is the smooth start-up and gentle idling of the engine, which extend the service life and ensure the hammer is accurate from the first blow.
Best pneumatic breakers
A pneumatic breaker is powered by compressed air, which pushes the tool tip under very high pressure. To provide this pressure, a compressor is needed, and its size directly depends on the power of the tool. Simply put, you cannot connect a powerful hammer to a small compressor with a small receiver and work. An industrial device is required. All this makes it almost impossible to use pneumatic tools in everyday life, and there is no need for it, if you do not plan to break concrete piles or FGC.
5 Concorde (CD-MO-3)
Modern manufacturers are constantly competing for originality. It is enough to look at any Bosch or Makita tool to understand how much time is devoted to design and ergonomics. But often, the classic is the best solution, and for pneumatic jackhammers this works just fine. Well, it's hard to come up with something original and new here. We can say that the classic design is the best.
Before us is just such a classic hammer, in which there is nothing new. This is a Russian manufacturer that has been on the market for a long time. He releases the instrument at the most democratic prices. For example, this hammer costs only 7 thousand rubles, which is very little for a tool of this class. What's the secret? Probably because the brand does not strive to create something new. Common hammer. They were used 10, 20 and even 50 years ago. It is difficult to say whether this is good or bad, but to this day, such or similar hammers are most often found in production, in contrast to the original works of Bosch or Makita.
4 SUMAKE ST-2200A / H
A jackhammer, electric or pneumatic, is not the most convenient tool in terms of working with it. Anyone who has ever used it knows how much hands get tired even after a few minutes of work. It doesn't matter if we're talking about a huge, industrial hammer, or a compact, low-power device. Manufacturers are constantly trying to improve ergonomics, and, apparently, this brand has succeeded best of all.
At first glance at this miniature hammer, it is difficult to say how easy it is to use, so let's turn to the reviews of people who have already bought it. And they are mostly positive. It turns out that this shape of the handle and the location of the button are quite convenient. The hammer can be operated with either one hand or two. By the way, the double grip appeared here for a reason. Despite the compact size of the instrument, its power is almost 10 joules, that is, it will be very difficult to hold it with one hand.
3 Wester MH-10
Remembering German quality, the first thing that comes to mind is Bosch. She is known all over the world, and few people think that there are many other brands in Germany that produce tools that are not inferior in quality to the eminent brand. Before us is one of them. If you have never heard of this manufacturer, it is only because he does not conduct aggressive marketing, but he is praised in reviews, and is often purchased at large enterprises and construction projects.
This is the best air hammer in a compact form factor. Yes, he is not capable of punching a hole in thick concrete. The impact force is only 4 joules. Of course, for a standard hammer this is very little, but for such a "kid" it is more than enough. It is the most compact instrument and is a miniature copy. It is powered by compressed air and produces up to 3.6 thousand blows per minute. The body is completely metal, excluding the plastic covers in the area of the handle, made to facilitate the operation of the instrument.
2 ARCHIMEDES MW510
Before us is the simplest jackhammer, standard configuration. There is nothing outstanding here, except for the force of the blow.Here it is 45 joules according to the documents, although as they say in the reviews, the real force is much greater, and easily reaches 60 or even 65 joules. For what purposes the manufacturer underestimated this indicator is not clear, since the price of the tool corresponds to higher characteristics.
It's difficult to talk about the advantages of a standard hammer, but here the shape of the handle has been slightly changed and the button that activates the tool has been shifted. As a result, it's easier to use. It should be noted that this form factor is not an invention of this manufacturer. Makita and Bosch have been doing something similar on their instruments for a long time, although they cost more. Is this hammer the best? Probably not, since Russian manufacturers have such tools, and they are much cheaper, and there will be no problems with spare parts, which cannot be said about a little-known Chinese brand.
1 Bison "Concrete Breaker" (1600 W)
The main problem with any jackhammers is high vibration levels. It is very difficult to work with them for a long time, and people who constantly use this tool even develop occupational diseases and deformities. All manufacturers are struggling with vibration. And the Zubr company did it in the best possible way. Before us is the most "calm", so to speak, a jackhammer.
It is equipped with several levels of vibration damping. They are located in the tip area, as well as in the handle and at the connection to the compressor. Working with such a tool is as comfortable and convenient as possible, even for a long time. True, the manufacturer had to sacrifice a little the total power of the instrument. Here it is only 35 joules, which is quite small for a 17 kilogram hammer. Also, this hammer is praised in reviews for its structural reliability and long service life. All these factors make it possible to apply the epithet "best" to him and place him in an honorable place in our rating.
